Multi Terminal Connecting Cable

Wireless Radio Control

Create a radio-controlled wireless flash control system by pairing a Radio Control Wireless Commander (FA-WRC1M) attached to a camera with a Radio Control Wireless Receiver (FA-WRR1) attached to a flash. This allows you to wirelessly control up to 15 flash units¹ in up to 5 groups² as far as 98' away. . Compatible with flash sync speeds up to 1/250 sec. for and up to 1/8000 sec. in High-Speed Sync (HSS) shooting mode⁵.

Command and control at your fingertips

Conveniently change flash settings for each flash or group by remotely controlling shooting mode, flash ratio and exposure compensation – all from the FA-WRC1M Radio Control Wireless Commander attached to the camera. TTL Mode Flash level7 is set automatically based on a value metered by the camera. Flash ratio can be set for each of 3 groups (A/B/C). Manual Mode Flash level7 can be manually set for each of 3 groups (A/B/C). Group Flash mode is set for each of 5 groups (A/B/C/D/E). Groups A-C can be set to [TTL] or [MANUAL] mode; groups D and E to [MANUAL] only.

Get every angle

Capture multiple angles by controlling remote shutter release on multiple cameras. With the Radio Control Wireless Commander (FA-WRC1M) mounted to the control camera and synchronized with up to 15 cameras connected to Radio Control Wireless Receivers (FA-WRR1) and dedicated Multi Terminal Connecting Cable (VMC-MM1)³ you can get multiple angles without the need for multiple camera operators.

Sync in Studio

Sync Terminals on the Radio Control Wireless Commander (FA-WRC1M) and Radio Control Wireless Receivers (FA-WRR1) can be connected to large studio monoblocks or flash heads⁴. Studio flashes can be either triggered by the Receiver connected via an optional PC sync cord that receives a wireless signal from the Commander or by the Commander connected via PC sync cord.

Overcome infrared limitations

Wireless Radio Control shines even in scenes where infrared communication is difficult. The wireless 2.4 GHz RF transmission radio control system gives you the ability to shoot scenes with distant locations where you need to control the light on your subject from as far as 98' or in strong sunlight where the sun washes out or objects block infrared ability and when objects block an infra-red signal from an IR flash system.

Dust and moisture resistant design⁶

Dust and moisture resistant design⁶ ensures that your flash system is a s rugged as the conditions you're shooting in.

Specifications

Weights and Measurements
Dimensions (Approx.)	Length: 31 1/2" (800mm)
Weight (Approx.)	0.8 oz (22g)

Documents

Warranty Card

Footnotes

^footnote1 Requires Radio Control Wireless Commander (FA-WRC1M), Radio Control Wireless Receiver (FA-WRR1) - sold separately and compatible camera and flash.

^footnote2 Max 5 groups in Group mode setting, 3 groups in TTL or Manual mode settings

^footnote3 Require Multi Terminal Connecting ULTI/Micro USB cable VMC-MM1 - sold separately

^footnote4 Commercially-available sync cable required. Flashes of sync voltage of less than 400V is required. Flash types with reversed sync terminal polarity can also be used.

^footnote5 Depending on camera specifications

^footnote6 Although the design is dust and moisture resistant, absolute protection from dust and moisture is not guaranteed.

^footnote7 Flash level controlled over 25 steps (1/1, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128, 1/256) in 1/3 EV step increments. 1/128 not selectable for High Speed Sync. If you are using an HVL-F32M Flash, set the flash level of the group that includes the HVL-F32M to 1/16 or higher when performing High-speed sync (HSS) shooting in MANUAL mode.